Aluminum hubs

fiat218 · Post by **fiat218** » Wed Feb 12, 2014 5:02 pm

Does any one know where I can get aluminum hubs ,other then miller mule ( Jason

narfire · Post by **narfire** » Wed Feb 12, 2014 7:57 pm

Any good machinists around you? The one near me make them for his dwarf cars.
Chris

fiat218 · Post by **fiat218** » Wed Feb 12, 2014 8:55 pm

narfire wrote:Any good machinists around you? The one near me make them for his dwarf cars.
Chris

Like a mechanic machines or a foundry?
Are they made in one piece or 2 piece and welded

paintdudeluke · Post by **paintdudeluke** » Wed Feb 12, 2014 9:13 pm

metal lathe.

fiat218 · Post by **fiat218** » Wed Feb 12, 2014 9:30 pm

paintdudeluke wrote:metal lathe.

There just one piece,correct

BEEK · Post by **BEEK** » Wed Feb 12, 2014 9:52 pm

I am assuming that Jason is out of stock

fiat218 · Post by **fiat218** » Wed Feb 12, 2014 9:54 pm

BEEK wrote:I am assuming that Jason is out of stock

Yes,he don't know when he will get some,but I will get some

I need some one to send me a hub,so they can copy it

narfire · Post by **narfire** » Wed Feb 12, 2014 10:50 pm

I'm thinking they would be made out of one block. For a couple or 4 I'd be thinking they might be a bit pricey. I could ask, but if one could take a pattern from an original and then use one of those fancy cad milling machines....

fiat218 · Post by **fiat218** » Wed Feb 12, 2014 11:07 pm

narfire wrote:I'm thinking they would be made out of one block. For a couple or 4 I'd be thinking they might be a bit pricey. I could ask, but if one could take a pattern from an original and then use one of those fancy cad milling machines....

It be the same as the steel hub ,I'm presuming , 200 per hub at Jason

BEEK · Post by **BEEK** » Wed Feb 12, 2014 11:08 pm

i want a set made with a different bolt pattern 5x114.3mm, as opposed to 4 x 98mm, this is for my project car, i already have the rear hubs for the irs, those have the 5x114.3mm pattern, the brake rotors and wheel selection is much greater at that pattern

MrJD · Post by **MrJD** » Fri Feb 14, 2014 12:38 pm

$800 for hubs + shipping/tax. Why do you want these fiat218?

azruss · Post by **azruss** » Fri Feb 14, 2014 2:50 pm

there are shops around that make adaptors for ATVs. I doubt if you will do better than a couple of hundred a whack. The turning is the easy part. the hard part is getting the holes concentric. This requires a mill, preferably a CNC mill.

fiat218 · Post by **fiat218** » Fri Feb 14, 2014 3:15 pm

MrJD wrote:$800 for hubs + shipping/tax. Why do you want these fiat218?

Just the front, lighter at the wheels

fiat218 · Post by **fiat218** » Fri Feb 14, 2014 3:17 pm

azruss wrote:there are shops around that make adaptors for ATVs. I doubt if you will do better than a couple of hundred a whack. The turning is the easy part. the hard part is getting the holes concentric. This requires a mill, preferably a CNC mill.

Never thought of that part, I just figure they would copy the steel ones

Aluminum hubs

Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs

Re: Aluminum hubs