I work for Beer

This is the place to discuss restoration problems, post questions or projects-complete or partial.
Post Reply
ez2wire

Re: I work for Beer

Post by ez2wire »

Does having to go into the house and want to fall to the floor laughing count as a major fit :)

After that initial reaction I was disappointed for Jeff, but when he told me he paid $700 on eBay for it, and it "supposedly" ran (Later determined term was "Cranked over") I was kind of expecting something of this nature.

Also knowing it was going to be a Christmas present, I couldn't in good conscience, let it stay in this condition.

The mechanicals simply weren't safe, and if he was going to invest in making it safe to drive, I felt I had to at least do what I could do to get the car looking better.

Given the car has been obviously be run hard and left wet, the 4 different colors and up to 11 coats of paint the car had been through. The body was surprisingly not completely shot (other than the doors, and trunk lid), LOTs of dings, dents, bondo, fiberglass, and assorted patches.

I had seen worse, that said it was a 1966 Pontiac GTO Convertible (Clone) and had a lot more upside in the value department. I paid $3500 for it at Carlilse, body was worse but it ran and brakes were good. Everything else was unuseable. Similar type restoration, and after investing $6000, I sold it for $15,000. The Fiat will probably have less in it total (including the shipping) than I paid for the GTO.
ez2wire

Re: I work for Beer

Post by ez2wire »

Fixed tailights, license plate lights, and bumper with Silver Rim paint. In the case of the bumpers and license plate lights I sanded them and painted with etching primer, and after I painted them I had painted with 3 coats of clear.

The tailight housings I used the same duplicolor silver rim paint, but prepped them simply by sanding and wiping down with acetone.

Think considering the budget, the overall look is nice, and cost came in at basically $0 as i had the paint and primer. Each if bought are about $8 each. So total cost would be less than $20.

Image

Well finishing up interior and trim. Just missing a lot of small parts (that are on the way), so kind of at a stalled point.

Not many pics yet to show..

Should have everything and be done with most everything this weekend.

Beer of the week - Legend Octoberfest... A Richmond Microbrew
User avatar
aj81spider
Patron 2020
Patron 2020
Posts: 1526
Joined: Fri Mar 11, 2011 9:04 am
Your car is a: 1974 Fiat 124 Spider
Location: Chelmsford, MA

Re: I work for Beer

Post by aj81spider »

You're doing a nice job on that car for short money. I wish you were in New England so I could ply you with beer!
A.J.

1974 Fiat 124 Spider
2006 Corvette
1981 Spider 2000 (sold 2013 - never should have sold that car)
User avatar
124JOE
Posts: 3141
Joined: Fri Jun 24, 2011 7:11 pm
Your car is a: 1978 124 fiat spider sport 1800
Location: SO. WI

Re: I work for Beer

Post by 124JOE »

i painted my 1800 logo red and polished up the high spots
Image
Last edited by 124JOE on Thu Nov 17, 2011 10:11 am, edited 1 time in total.
when you do everything correct people arent sure youve done anything at all (futurama)
ul1joe@yahoo.com 124joe@gmail.com
ez2wire

Re: I work for Beer

Post by ez2wire »

Thanks, wait till you see what I can do with black Lowes deck carpet, a yard of black vinyl, 3m upholstery spray adhesive, gorilla tape, and black vinyl spray paint, chrome polish, some judicious use of epoxy and emblem adhesive. :o
ez2wire

Re: I work for Beer

Post by ez2wire »

124JOE wrote:i painted my 1800 logo red and polished up the high spots
I was thinking of painting it.. But decided to leave it just polished.. Leaves some of the "original" patina on the car.. :P
fiat218
Posts: 5745
Joined: Fri May 16, 2008 5:06 pm
Your car is a: 1969 124 AS spider

Re: I work for Beer

Post by fiat218 »

sounds like a kit car
Jim
East Grand Forks MN
1970 Fiat Spider BS1 ( FOR SALE
1969 124 AS Spider
2017 Abrath
2018 Alfa Romeo 4c Spider
ez2wire

Re: I work for Beer

Post by ez2wire »

fiat218 wrote:sounds like a kit car
Only if I were resurrecting a kit car.

Use of original seats and door panels with no budget for seat covers. A little gorrilla tape to patch rips where needed.

Since the seats were brown, door panels tan, rear seat and side panels were red/pink.. Best way to fix all that scrub with soap and water then wipe the vynil with acetone. Before the acetone dries, thats when you spray with the vynil spray paint. I find wiping the vynil with the acetone it softens and opens the vynil pores to better adhere to the vynil paint. The end result is quite surprising if you have never used it like this before. Look on page three at the door panel, that was fixed that way.
fiat218
Posts: 5745
Joined: Fri May 16, 2008 5:06 pm
Your car is a: 1969 124 AS spider

Re: I work for Beer

Post by fiat218 »

patch cars dont last long
good luck with it all :) looks nice from pictures
Jim
East Grand Forks MN
1970 Fiat Spider BS1 ( FOR SALE
1969 124 AS Spider
2017 Abrath
2018 Alfa Romeo 4c Spider
ez2wire

Re: I work for Beer

Post by ez2wire »

Well this is better than a patch job.

That said, could you be any more of a downer. You know what they say, if you dont have anything nice to say...
fiat218
Posts: 5745
Joined: Fri May 16, 2008 5:06 pm
Your car is a: 1969 124 AS spider

Re: I work for Beer

Post by fiat218 »

:D
Jim
East Grand Forks MN
1970 Fiat Spider BS1 ( FOR SALE
1969 124 AS Spider
2017 Abrath
2018 Alfa Romeo 4c Spider
narfire
Posts: 3959
Joined: Sat Dec 27, 2008 2:14 am
Your car is a: 1980 124 spider
Location: Naramata B.C.

Re: I work for Beer

Post by narfire »

ez2wire wrote:Beer of the week - Legend Octoberfest... A Richmond Microbrew
Sent a pm
chris
80 FI spider
72 work in progress
2017 Golf R ( APR Stg. 1)
2018 F350 crew long box
jimmycakes401

Re: I work for Beer

Post by jimmycakes401 »

I like what you're doing with the bumpers. I have issues with my bumpers and won't be able to afford chrome. My wife does not want me to take them off. I've been debating using silver, getting chrome kits from eastwood or painting them black. I have an 81' with the big bumper too. Nice to see how it's coming out. I guess my car is also a "patch" car. Hope it lasts. Will never leave a garage. LOL
ez2wire

Re: I work for Beer

Post by ez2wire »

The paint I use is Duplicolor High Performance Wheel coating.. Tough and works well.. Used it on my Opel GT I restored, a 66 GTO clone, and it always comes out looking real nice..
akavinn1

Re: I work for Beer

Post by akavinn1 »

I think it looks great ! nice work .
Post Reply